Comparison between fluctuation of floating potential gradient and velocity of blob structure on HL-2A tokamak

Several results based on the Langmuir probes' data on the HL-2A tokamak are presented. The blob structures' radial and poloidal drift velocities, estimated by the gradient of floating potential and by time delay evaluation, are compared in different line-averaged density and electron cyclotron resonance heating conditions. A positive correlation is observed in the comparison between blobs' radial velocity estimated by the two methods mentioned above, regardless of the situation differences mentioned above. Correlation is also observed in the comparison between the blobs' poloidal velocity estimated by the two methods in different situations, while a shift due to the different line-averaged density is observed. These results imply that the radial gradient of floating potential may have some value as a reference during data analysis in low-parameter discharge.     

响应面曲线法优化贵州某磷块岩浮选工艺研究

对贵州某沉积钙质磷块岩进行了浮选工艺研究。采用H₂SO₄为氟磷灰石抑制剂、BW-1为白云石捕收剂,进行了浮选单因素试验; 在此基础上进行了正交试验,并采用响应面曲线法进行了浮选条件优化。确定了最佳浮选条件为: 磨矿细度-0.074 mm粒级占60%、H₂SO₄用量13.20 kg/t和BW-1用量400 g/t。采用一段反浮选试验流程,可得到精矿品位30.94%、回收率92.45%的磷精矿。研究结果表明,磨矿细度与H₂SO₄用量的交互作用对精矿品位影响显著,H₂SO₄用量和BW-1用量的交互作用对精矿回收率影响显著。     

甲基氯硅烷精馏流程的模拟与优化

采用Aspen plus软件对工业七塔精馏过程进行全流程建模与模拟，优化工艺参数，研究了新的精馏节能工艺。对一甲塔等7个精馏塔采用双因素水平的灵敏度分析，考察了塔釜采出率、回流比、进料位置和塔顶压力对产品浓度和热负荷的影响，确定一甲塔最优的工艺参数：塔釜摩尔采出率为0.92，摩尔回流比为130，塔顶压力为0.18 MPa，总理论板数为400，在210块理论板位置进料。在此基础上，针对高能耗的脱高塔/脱低塔，模拟研究了双效精馏新工艺，新工艺可节省39.70%的年总成本；针对一甲塔模拟研究了热泵精馏新工艺，新工艺可降低41.42%的年总成本。     

桁架式火星探测器的着陆缓冲特性分析

着陆缓冲机构是着陆器实现行星探测软着陆的关键部位之一,它的缓冲性能直接关系到着陆器是否能安全地在行星表面实现软着陆。根据某院提供的火星着陆器模型,在三维建模软件中建立着陆器的合理简化模型,为了提高分析着陆器软着陆过程冲击响应的准确性,采用MSC公司的Patran/Dytran有限元软件,用瞬态动力学的方法对着陆器的缓冲性能进行分析。仿真结果与试验数据十分吻合,着陆器的缓冲和传力性能良好。因此,采用拉杆缓冲的桁架式火星着陆器是可行的,仿真结果与试验数据也为今后的火星探测提供了参考。     

高温气冷堆舱室抗商用飞机撞击的耦合数值分析

本文建立了大型商用飞机撞击典型高温气冷堆核电站反应堆舱室的非线性有限元模型，计算中混凝土舱室直接采用工程用钢筋混凝土的损伤塑性本构模型，飞机结构采用Johnson-Cook本构模型。对飞机高速撞击高温气冷堆核电站反应堆舱室非线性撞击过程进行模拟计算，得出正面和侧面撞击条件下的撞击载荷曲线、撞击位移云图、反应堆舱室混凝土破坏情况等结果。评估表明，反应堆舱室结构在撞击条件下的整体损伤微小，可为保护内部关键设备提供重要的屏障功能。     

2219铝合金搅拌摩擦焊和钨极保护焊焊接件残余应力的中子衍射研究

利用中子衍射法对2219铝合金搅拌摩擦焊（FSW）和钨极保护焊（TIG）焊接件开展了三维残余应力测量，并对残余应力分布规律进行了分析。结果表明：焊接件的纵向残余应力数值较大；FSW焊接件残余应力整体较TIG焊接件的小；FSW和TIG焊接件的残余拉应力最大值分别为101 MPa和174 MPa，FSW焊接件残余拉应力最大值较TIG焊接件的小；FSW残余拉应力最大值处于轴肩边缘，且前进侧峰值大于后退侧峰值；TIG焊接件残余拉应力最大值处于焊缝边缘。通过中子衍射实验获得的焊接件残余应力分布，将可用于焊接工艺的优化与焊接件的寿命预测。     

The impact of recrystallisation on the freeze-thaw cycles of red seabream (Pagrus major) fillets

Recrystallisation often occurs in the freeze-thaw cycles and results in poor food quality. This study was undertaken to analyse the effects of recrystallisation on the changes of protein conformation and moisture migration within red seabream fillets after the freeze-thaw cycles. The UV second-derivative spectroscopy, intrinsic fluorescence measurement and Raman spectroscopy were employed to evaluate the protein conformational changes. The Low-field NMR spectra analysis was used to evaluate moisture migration. The results indicated that the freeze-thaw cycles altered the secondary and tertiary structure of proteins. It was noticed that interactions between water and protein molecules were decreased gradually and eventually induced the thermal instability of the myosin molecules. The immobilised water content declined and the free water content increased. There were significant destructions in fillet muscle microstructure. These observations unambiguously reflect how the recrystallisations affect the protein conformation and moisture migration patterns of red seabream fillets during freeze-thaw cycles.